Just How To Install A Bath Tub (For Novices).

Additional Information

We've stumbled on this great article pertaining to A Step-by-Step Guide to Installing a Bathtub listed below on the net and figured it made perfect sense to share it with you in this article.


Tools You Need to Install a New Bathtub
Installing a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the job can relocate easily; if you need to open up a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the task and also fit attempting it. Rather than hiring a service provider to take over a halfway-completed job, it is better to take into consideration employing one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly aid you mount a brand-new bathtub in your shower room if you have actually already acquired a new tub and also don't require to alter the setup of your previous water pipes.
Your devices and material list ought to consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing taps can be fairly bothersome due to the limited gain access to that is usually the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
    Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
    If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Secure the faucet in position with the maker given backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Making use of both wood boards under its feet, put the bathtub in the needed placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
    The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
    To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
    Turn on the water system as well as check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and also the typical outlet for leakages.
    Finally, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the tub must wait until the tub has been utilized at least when as this will certainly settle it right into its final setting.

    Getting ready for the Installment


    Firstly, the supporting frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.

    Tiling Around the Bathtub


    In the area where the bath meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, bring about complications with dampness and possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into account this movement before securing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    I ran across that page about How to Install a Bathtub Yourself when looking around the search engines. Make sure you set aside a second to distribute this page if you enjoyed reading it. Thank-you for taking the time to read it.



    Quote & Schedule

    Leave a Reply

    Your email address will not be published. Required fields are marked *